1. 您好,歡迎光臨萊州聚峰機械有限公司官方網站! 鄭重聲明 購機 售后 聚峰官微

            全國咨詢熱線

            400-879-1999

            您的位置: 首頁 > 新聞資訊 > 合作資訊 >
            自動混凝土攪拌車的高噪聲高溫原因!
            來源:http://www.mag2vow.com/ 日期:2021-07-05
            在炎熱的夏天,混凝土自動裝料攪拌機的內部噪音和溫度會增加。夏季溫度不高,但這可能是由于發動機或汽車中機油的溫度所致。
            In hot summer, the internal noise and temperature of the automatic concrete charging mixer will increase. The temperature is not high in summer, but this may be due to the temperature of engine oil or automobile oil.
            1.洗車水箱中的水量不足以清除。向洗車水箱注滿水。
            1. The water in the car washing water tank is not enough to remove. Fill the car wash tank with water.
            2.如果吸管的進氣口堵塞或堵塞,可以檢查并擰緊吸管。不要呼吸空氣。
            2. If the air inlet of the straw is blocked or blocked, check and tighten the straw. Don't breathe air.
            3.油箱液位過低,并且油液中的空氣被吸入泵中。如果發生這種情況,您可以添加帶有相同標簽的液壓油。
            3. The liquid level of the oil tank is too low, and the air in the oil is sucked into the pump. If this happens, you can add hydraulic oil with the same label.
            4.如果泵的安裝支架不夠牢固,則在工作期間會產生振動和噪音。在這種情況下,可以加固油泵支架。
            4. If the mounting bracket of the pump is not firm enough, vibration and noise will be generated during operation. In this case, the oil pump bracket can be reinforced.
                            中科攪拌車價格
            5.堵塞的濾芯會使吸油困難或不充分。在這種情況下,請清潔濾芯或更換濾芯。
            5. Blocked filter element will make oil absorption difficult or insufficient. In this case, clean the filter element or replace the filter element.
            6.油冷卻風扇未打開。卸下:打開冷卻風扇。
            6. The oil cooling fan is not turned on. Remove: turn on the cooling fan.
            7.如果液壓油不符合要求或油太粘,請更換符合標簽要求的低粘度液壓油。
            7. If the hydraulic oil does not meet the requirements or the oil is too viscous, please replace the low viscosity hydraulic oil that meets the label requirements.
            8.儲罐中有堅硬的混凝土。如果發生這種情況,請及時清理并鏟起。
            8. There is hard concrete in the tank. If this happens, clean up and shovel in time.
            9.輸入萬向節軸之間的連接角度以及萬向節軸與取力器之間的連接角度太大,如果松開會產生噪音,在這種情況下,請在時間內檢查并擰緊。
            9. The connection angle between the input cardan shaft and the connection angle between the cardan shaft and the power take-off are too large. If it is loosened, noise will be generated. In this case, please check and tighten it within time.