1. 您好,歡迎光臨萊州聚峰機械有限公司官方網站! 鄭重聲明 購機 售后 聚峰官微

            全國咨詢熱線

            400-879-1999

            您的位置: 首頁 > 新聞資訊 > 合作資訊 >
            自上料攪拌車清洗滾筒需要注意什么?
            來源:http://www.mag2vow.com/ 日期:2021-06-07
            1、自上料攪拌車在施工現場卸料完畢后,應立即用拌和車隨帶的軟管沖刷進料斗、出料斗、卸料溜槽等處,鏟除粘附在車身遍地的污泥及混凝土。在回來拌和站的途中,應向拌和筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。
            1. After the loading mixer is discharged at the construction site, the feeding hopper, discharging hopper, discharging chute, etc. shall be immediately washed with the hose attached to the mixer, and the sludge and concrete adhered to the vehicle body shall be removed. On the way back to the mixing station, 150-200l water shall be injected into the mixing drum to clean the concrete residue bonded on the wall and blades of the drum.
            2、每天作業完畢后,司機應負責向拌和筒內注入清水并高速(14—18轉/分)旋轉5—10分鐘,然后將水排去,以確保筒內清潔。用高壓水清洗拌和筒各個部分時,應注意避開儀表及操縱桿等部位。壓力水噴嘴與車身油漆外表間的間隔不得小于40厘米。
            2. After the completion of daily operation, the driver shall be responsible for injecting clean water into the mixing drum and rotating at high speed (14-18 RPM) for 5-10 minutes, and then discharging the water to ensure the cleanness of the drum. When cleaning each part of mixing drum with high-pressure water, pay attention to avoid instrument and control rod. The distance between the pressure water nozzle and the paint surface of the car body shall not be less than 40 cm.
                        中科自上料攪拌車
            3、鏟除拌和筒內外積污及殘存的混凝土渣塊時,以及在機修人員進入筒內進行檢修和焊補作業時,需先關閉轎車發動機,使拌和筒完全停止滾動。在機修人員進入筒內作業期間,必須確保拌筒內通風良好,空氣新鮮,無可然氣體及有害塵埃,氧氣供應充足。在筒內運用電動工具操作時,操作人員必須有良好的絕緣保護。
            3. When removing the dirt and residual concrete slag inside and outside the mixing drum, and when the maintenance personnel enter the drum for repair and welding, the car engine should be turned off first to stop the mixing drum rolling completely. During the operation period, the maintenance personnel must ensure that the mixing cylinder is well ventilated, the air is fresh, free of combustible gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, operators must have good insulation protection.
            4、作業時,不得將手伸入旋轉的拌和筒內,禁止將手伸入主卸料溜槽和加長卸料溜槽的銜接部位主動,主動上交拌和車在作業時應注意什么以免發生事故。
            4. During operation, do not put your hand into the rotating mixing drum. Do not put your hand into the joint of main discharge chute and extended discharge chute. Take the initiative to hand in the mixing truck. What should you pay attention to during operation to avoid accidents.