1. 您好,歡迎光臨萊州聚峰機械有限公司官方網站! 鄭重聲明 購機 售后 聚峰官微

            全國咨詢熱線

            400-879-1999

            您的位置: 首頁 > 新聞資訊 > 行業新聞 >
            自動上料攪拌機輪胎的維保方法!
            來源:http://www.mag2vow.com/ 日期:2021-07-02
            由于自身負載一直都在變化,因此自動上料攪拌機對于輪胎的要求是比較高的。所以做好輪胎的日常維護檢查是十分有必要的,下面我們就來具體介紹一下自動上料攪拌機輪胎的維保方法,感興趣的朋友不要錯過。
            As the load has been changing, so the requirements of automatic feeding mixer for tires are relatively high. So it is very necessary to do a good job in the daily maintenance and inspection of tires. Now let's introduce the maintenance methods of automatic feeding mixer tires. Interested friends should not miss it.
            1、一般情況下,在車輪加載并運行2-5小時后,需要檢查車輪上的螺母。交叉擰緊維護手冊中顯示的扭矩值,如果8小時后螺母仍然擰緊,則檢查扭矩間隔長至150小時。
            1. In general, after the wheel is loaded and operated for 2-5 hours, it is necessary to check the nuts on the wheel. Cross tighten the torque value shown in the maintenance manual. If the nut is still tightened after 8 hours, check the torque interval as long as 150 hours.
            2、在保持輪胎適當氣壓的同時,用閥門檢查氣壓。如果輪胎熱時需要充氣,則檢查同一軸上的另一個車輪,并在低壓下充氣,使兩者保持一致,熱的輪子氣壓需要等于或高于冷的車胎氣壓,檢查車輪損壞情況,檢查紋路和移走危險的東西。
            2. Check the air pressure with the valve while maintaining the proper air pressure of the tire. If the tire needs to be inflated when it is hot, check the other wheel on the same axle and inflate it under low pressure to keep the two consistent. The pressure of the hot wheel needs to be equal to or higher than that of the cold tire. Check the damage of the wheel, check the grain and remove dangerous things.
                                中科自上料攪拌機
            3、車輪和輪胎內的氣壓會引起叉車輪胎部件爆炸,造成較大的人員傷亡,因此在卸下輪胎前應先放掉空氣,如果氣壓低于正確氣壓的80%,需要在安全的地方卸下輪胎并充氣,并根據輪胎充氣部位進行充氣,充氣時振作起來,使用一個遠程氣泵,這樣人可以遠離輪胎。
            3. The air pressure in the wheel and tire will cause the explosion of the forklift tire components, causing great casualties. Therefore, the air should be released before unloading the tire. If the air pressure is lower than 80% of the correct air pressure, the tire should be unloaded and inflated in a safe place, and the inflation should be carried out according to the inflation position of the tire. When inflating, cheer up and use a remote air pump, So people can stay away from the tires.
            4、檢查邊緣是否彎曲或損壞。檢查是否有丟失或松動的物品,拆下粘在車輪上的金屬線,確保車輪緊固,交叉擰緊車輪需要注意,當車輪沒有車輪卸載時,它需要給車輪上的螺母上油,在法蘭和車輪螺母之間以及螺紋中滴下兩滴油。
            4. Check the edges for bending or damage. Check whether there are missing or loose items, remove the metal wire stuck on the wheel, ensure that the wheel is tight, cross tighten the wheel. When the wheel is unloaded without wheel, it needs to oil the nut on the wheel, and drop two drops of oil between the flange and the wheel nut and in the thread.
            以上就是小編為大家介紹的自動上料攪拌機輪胎的維保方法,輪胎安全是攪拌機可以安全生產的前提,沒有輪胎將寸步難行,所以一定要維護好輪胎。如想了解更多資訊內容請點擊官網:中科自上料攪拌機http://www.mag2vow.com
            The above is the maintenance method for the tires of automatic feeding mixer introduced by Xiaobian. Tire safety is the premise for the safe production of mixer. It will be difficult to move without tires, so we must maintain the tires. For more information, please click on the official website: Zhongke self feeding mixer http://www.mag2vow.com 。